Pontiac Firebird & Trans Am Twin Turbo Kit
Twin turbo component package for 1967–1979 Pontiac Firebird and Trans Am models equipped with a Pontiac 326, 350, 400, or 455 engine. Includes two T3 turbochargers, stainless steel manifolds, a front-mount intercooler, charge piping, oiling kits, and supporting accessories for a custom turbo installation.
Fitment
- 1967–1979 Pontiac Firebird and Trans Am with Pontiac 326, 350, 400, or 455 engines.
- Pontiac engines only. Not for Chevrolet small-block (SBC) engines.
- Excludes Ram Air IV applications.
- Verify engine configuration, exhaust-port compatibility, and engine-bay clearance before ordering. Fabrication and modifications may be required.
Turbochargers & Exhaust Components
- Two T3 turbochargers: .57 compressor wheel trim, .50 A/R compressor housings, .63 A/R turbine housings, oil-lubricated floating bearings, 3-inch inlets, 2-inch outlets, and 1/8-inch NPT oil inlets. Includes oil-fitting gaskets and mounting studs.
- Two stainless steel turbo manifolds: TIG-welded 321 stainless steel construction, 1-5/8-inch primary tubes, thick flanges, and a polished, ported design. Includes stainless steel V-band clamps.
- Two internal wastegate kits: Designed for the included turbochargers, with a listed starting pressure of 8 PSI. Includes V-band downpipe flanges and clamps. This pressure specification is not a recommended boost setting for every engine.
- Two DIY downpipe kits: 2.5-inch mandrel-bent stainless steel piping with TIG welds and pre-installed oxygen-sensor bungs. Custom fitting and exhaust connections are required.
- Heat wrap: One 50-foot roll, 1 inch wide.
Intercooler & Intake Components
- Front-mount intercooler: Lightweight aluminum construction with TIG-welded joints.
- 2.5-inch aluminum piping kit: Two 90-degree bends, two 60-degree bends, two 45-degree bends, and two straight pipes.
- Couplers and clamps: Two 2.5-inch 90-degree silicone couplers, six 2.5-inch straight silicone couplers, and 16 stainless steel worm-gear clamps.
- Blow-off valve kit: Includes installation hardware and flanges for placement during fabrication.
- Two cone air filters: Washable design.
Oiling, Fuel & Boost Accessories
- Two turbo oiling kits: Oil-feed lines, oil-return lines listed at 550 PSI, feed and drain fittings, gaskets, clamps, and installation hardware.
- Manual boost controller: CNC-machined anodized aluminum construction with installation kit. Final boost settings must be established during tuning.
- Fuel pressure regulator and filter kit: Adjustable regulator, pressure gauge, installation kit, and -6AN billet aluminum inline filter. Verify compatibility with your fuel system.
- Oil catch can: Polished finish with installation kit for the breather system.
- Boost gauge: 52 mm gauge with backlighting.
- Electronic turbo timer: Digital LED display, automatic mode, pigtail, and additional wiring. Requires integration with the vehicle's electrical system.
Cooling & Battery Relocation
- Slimline cooling fan: Reversible push/pull design with curved blades and mounting tabs. Listed thickness is 1.25 inches at the outer perimeter and 2.50 inches at the inner section.
- Battery relocation kit: Aluminum construction with relocation cables, straps, and hardware.
Installation & Tuning Notes
Professional installation and custom tuning are strongly recommended. Plan for intercooler and piping placement, downpipe fabrication, oil-feed and drain routing, battery relocation, wiring, and heat management. Additional fuel-system, engine-management, exhaust, and mounting components may be required to complete your specific build.
Power output and safe boost depend on engine condition, fuel delivery, ignition timing, fuel quality, and tuning. No horsepower gain or stock-engine boost level is guaranteed. Confirm applicable emissions requirements before installation or road use.